Article Safety

AGS SWG Call for Safety Alerts

- by

Dear Member,

 

 

MESSAGE FROM THE SAFETY WORKING GROUP CHAIRMAN – CALL FOR SAFETY ALERTS

 

The Safety Working Group would like to encourage the sharing of lessons learnt from accidents, incidents and near misses on a more regular basis. This information is normally obtained from members of the group raising issues during the meetings which often have directly affected their organisations or through discussing Safety Alerts. However, we rarely receive Safety Alerts and so often the issues we can discuss are limited to the experiences of the members of this working group which can be argued does not necessarily reflect the industry or membership as a whole.

 

The wider construction industry seems to be much better at issuing Safety Alerts but many of these are not related to AGS member’s work and so often they are not relevant. It is the belief of the Safety Working Group that we are missing valuable ‘lessons learnt’ or an opportunity to raise awareness of current issues and we would like this to improve.

 

This is an appeal for the AGS membership to ‘up its game’ and to start being more pro-active in the generation of Safety Alerts. The issuing of Safety Alerts is a simple system which can be used to not only raise awareness of substandard products or poor practice but also to reiterate safety messages, provide lessons learnt and provide warnings. Some companies are reluctant to issue Safety Alerts as they believe that any accident, incident or near miss will look bad on them or clients may believe their organisation has unsafe practices. This is a very negative view of Safety Alerts whereas they should be looked at as a proactive approach to accidents, incidents and near misses and a desire to improve safety.

 

We would like to receive any Safety Alerts which have been issued to members but would also really like to receive Safety Alerts generated by our members. Please help.

 

 

 

Yours faithfully,

For the Association of Geotechnical and Geoenvironmental Specialists

 

 

JULIAN LOVELL

Chair of the Safety Working Group

 

Report Safety

Safety Group Report

- by

Julian Lovell, Chairman, AGS Safety Working Group writes:

Below is the latest report from our Safety Group which this quarter has been tackling issues on guidance, the new CDM regulations and collaboration with the British Drilling Association (BDA).

AGS Safety Guidance

The working group has been working consistently to progress the guidance available to the industry. Progress has been steady throughout the year. Most guidance goes through two if not three reviews which effectively means 3 to 6 months from initial draft and the most effective reviews are carried out by the committee either in a face to face meeting or on one occasion an on-line meeting.

Guidance which has been published since the last meeting:

  • Use of Scaffolding/Temporary Working Platform
  • Lifting Operations and Equipment used in Drilling Operations Guidance on CSCS Registration
  • Driving at Work

Guidance close to completion:

  • PPE
  • Manual Handling
  • Training and Competence
  • AGS Health and Safety Training Standards Health Surveillance

Website

Currently all published guidance is freely available from the AGS website. The SWG has discussed this matter and believes that all of the safety guidance should be freely available in front of the member’s portal.

Where individual guidance links together we would like hyperlinks so that you can move between them. This should be part of the new website functionality specification. The web pages should have photographs and images and not just a list of links to guidance. The guidance will also be split into sections to try to make it easier to find what you want. Currently, we are waiting for the development of standard templates before we can provide further input to the new section within the new website.

BDA

The BDA has completed a new version of its Safety Manual and this is likely to be available digitally in the next month or so. Currently, they are deciding how and who it is distributed to but it is likely to be free to members. Unsure if it will be sold on the wider market.

There have also been ongoing discussions between the BDA and AGS regarding a closer working relationship. The AGS SWG has discussed on numerous occasions how much of an overlap there is and has offered to set up a joint working group. The BDA have reported back that they initially want to establish their own safety committee which has not met for over 12 months. They will then re-visit the idea of working with the AGS.

BDA have agreed to sponsor a session at Geotechnica which will be a Health and Safety session.

The BDA also spoke to the SWG about the BDA Audit. This scheme has been brought in to allow companies to assess the ongoing competence of the drill crews and to comply with BS 22475: Part 2. The auditee has to have already achieved the Land Drilling NVQ but this will look more closely in to how the driller is operating on site and complying with legislation, guidance and good practice. The BDA Training and Education Committee is currently working with Equipe to strengthen the Audit so that it requires the auditee to be able to prove a high standard of knowledge and application of both quality and safety. It is hoped that this will be linked in to the work to improve the current Land Drilling NVQs and in time to develop a Level 3 Advanced Lead Driller qualification.

Safety awareness and CSCS

The CSCS have been advised by the construction industry that there are too many loopholes in the CSCS card scheme. The CSCS card should represent the work activity being performed on site by that individual. The current clamp down has seen the requirement to attend a one day approved Health, Safety and Environmental awareness course if a GREEN labourer’s card is required. This is in addition to the CSCS touch screen test. Whilst this sounds initially like a good initiative to reduce the number of generic cards and promote training there are concerns. The concerns are that

  • it may lead to similar generic cards such as the WHITE Construction Related Operatives (CRO) card requiring something similar or being withdrawn
  • the promotion of generic Health and Safety training.
    The CRO card is commonly used across the geotechnical industry under the title Ground Specialist.New Standards BS EN 16228 – Drilling and foundation equipment.The new standard is seen to be the European wide requirements for rig guarding but they are actually a lot more detailed and cover all safety aspects of operating drilling equipment across sectors and rig types. Most organisations have still not looked to see if changes to UK practice or obligations on rig users or manufacturers has changed. AGS has told BDA that as the trade body for drilling they should be advising industry on these matters. One AGS member believes that it downgrades the importance of guarding in reference to trapping distances. There will undoubtedly be other areas which need to be considered. The BS was live from the end of October 2014.

    Construction Design and Management Regulations, 2015

    The changes to the CDM regulations was discussed, majority of the group felt more responsibility had been passed onto the client and they would now have to consider risk as well as the cost of the project. Julian Lovell noted the HSE encourages industry interpretation, and thought it was important guidance was produced to reflect the industry. The group agreed and recognised the re-education of clients would be the hardest transition. It was agreed joint industry guidance with the BDA and the Federation of Piling Specialists (FPS) would be ideal. Julian, Madeleine Bardsley, Adam Latimer and Jon Rayner agreed to contribute to the joint industry guidance on behalf of the AGS. Ann-Marie Casserly raised the proposal at the FPS Safety & Training meeting and Julian contacted BDA. Currently all parties agree that it would be a good initiative but neither FPS nor BDA could provide time or resources at the moment.

    Equipe are currently arranging a FREE one day seminar/discussion forum for Health and Safety in the geotechnical industry on 4th March at their training rooms near Banbury. The day is aimed to open up debate on HS&E matters including:

  • How the industry should adopt and interpret the requirements of CDM 2015
    • Can we educate the client?
    • Can CDMCs become Principal Designers?
    • Can the industry cope with the increased demand to act as Principal Contractor?
  • Will it increase resources and costs to complete CDM jobs?
  • Why companies might consider Health Surveillance

Safety Alerts

The Safety Working Group would like to receive copies of safety alerts relevant to member’s activities so that lessons can be learnt. The most valuable messages often come from Near Misses and it is hoped that we can start a regular item in the newsletter but we have to have items sent from the membership.